• Using 9V battery (Not included)
• Inductors, capacitors , diodes, dual diode , mos, transistor, SCR , the regulator, LED tube , ESR,
• Resistance,Adjustable potentiometer
• Resistance : 0.1 ohm resolution, maximum 50M ohm
• Capacitor : 25pf -100,000 uf
• Inductors : 0.01mh-20H
• Automatic detection of NPN and PNP transistors, n-channel and p-channel MOSFET,
diode (including double diode), thyristor, transistor, resistor and capacitor and other components
• Automatic test the pin of a component, and display on the LCD
• Can detect the transistor, MOSFET protection diode amplification coefficient
and the base to determine the emitter transistor forward biased voltage
• Measure the gate and gate capacitance of the MOSFET threshold voltage
• Use 12864 liquid crystal display with green backlight
Specifications: For you reference
1: One -button operation, automatic shutdown .
2: Only 20nA shutdown current.
3: Automatically detect NPN, PNP bipolar transistors , N -channel and P -channel MOS FET,
JFET , diodes , two diodes, thyristors small power unidirectional and bidirectional thyristor.
4: Automatic identification components pin arrangement .
5: Measuring bipolar transistor current amplification factor and base - emitter threshold voltage.
6: Via the base - emitter threshold voltage and high current amplification factor to identify Darlington transistors.
7: Can detect bipolar transistors and MOS transistors protection diodes.
8: Measuring the gate MOS FET threshold voltage and the gate capacitance.
9: Can simultaneously measure two resistors and resistor symbol is displayed.
Displayed on the right with a decimal value of 4 .
Resistance symbol on both sides shows the pin number.
So you can measure the potentiometer.
If the potentiometer wiper is not transferred to an extreme position ,
we can distinguish the middle and both ends of the pin.
10: Resistance measurement resolution is 0.1 ohms , 50M ohms can be measured .
11: Can measure capacitanceCan measure capacitance of 30pF-100mF , resolution 1pF.
12: 2uF more capacitors can simultaneously measure the equivalent series resistance ESR values.
The two can be displayed with a decimal value , resolution 0.01 ohms.
13: Can be in the correct order and the diode symbol display two diodes , and gives the diode forward voltage.
14: LED is detected as a diode forward voltage higher . Combo of the LED is identified as two diodes.
15: Eeverse breakdown voltage is less than 4.5V Zener diode can be identified.
16: Can measure a single diode reverse capacitance.
If the bipolar transistor connected to the base and collector or emitter of a pin ,
it can measure the collector or emitter junction reverse capacitance .
18: can be obtained with a single measurement rectifier bridge connection.
LCR-TC And LCR-T7 Detailed Introduction:
Features :
• It can be widely used to detect NPN and PNP transistor, capacitor, resistor, diode, triode, N-channel and P-channel MOSFET, IGBT, JFET, triac and battery etc.
• It can also be used to detect infrared wave shapes.
• It can also detect Zener diode and has the function of self-calibration.
• After detection, align the infrared remote controller with the "IR" light, press the button in the remote controller, if the detector successfully decode it, it will display the data code and infrared wave form.
• One button operation, Automatically detect and shutdown, and you can press the multi-function button to close the detector too.
• Put the pins of component in corresponding area, then dial the small handle and the detector will test it automatically, finally the results will display on the back light TFT screen clearly.
• Not like the usual black and white screen, this detector will show results in color.
Specificaties:
1: Display: 1.8Inch TFT display
2: Resolution: 160x128
3: Diode Range: <4.5V
4: Zener Diode: Transistor Detect Area: 0.01-4.5V
5: Zener Diode Detect Area: 0.01-30V
6: Triac Range: IGT < 6mA
7: Capacitance: 25pF-100mF
8: Resistance:0.01-50MΩ
9: Inductance:0.01mH-20H
10: Battery: 0.1-4.5V
11: Power Mode: Rechargeable lithium battery(INCLUDED)
12: Item Size: 8.8x8x2.8cm / 3.47x3.15 x 1.10in
13: Item Weight: 111.5g / 3.94oz
14: Size: 14.5x12x2.7cm / 5.71x4.73 x 1.06in
15: Weight: 114g / 4.02oz
LCR GM328 Detailed Introduction:
Features:
• Digital LCD display for easy readings, can display measured data and graphics.
• Rotary switch control, a key measurement for convenient use.
• Main chip is the DIP, easy for electronic enthusiasts to DIY or update the main chip.
• Use 9V battery(not included), can also use DC power(DC 6.8-12V).
• Automatic shutdown, shutdown current is only about 20nA.
• Automatically detects NPN and PNP transistors, FET, diodes, dual diode, thyristor, SCR, automatic identification of the transistor pinout.
• Test NPN and PNP transistor common-emitter current amplification factor, the base-emitter threshold voltage, off the collector - emitter leakage current.
• Support 2 resistors measurement, show its positive and negative, on-state voltage.
• Resistance measurement maximum resolution 0.01Ω, can be measured up to 50MΩ.
• Automatically test the pins of a component and show on the display.
• Measure FET gate threshold voltage and gate capacitance.
• For the following 2100Ω resistor while measuring its inductance measuring range from 0.01mH - 20H.
• Can be used as signal generator and frequency meter: frequency range from 1Hz-2MHz and can generate 1%-99% PWM(pulse width modulation) signals.
Specifications:
1: Display: 160*128 LCD
2: Power Supply: 1 * 9V Battery(not included); DC 6.8-12V
3: Current: Approx. 30mA
4: Resistance Measurement: Max. 50MΩ
5: Resistance Resolution: 0.01Ω
6: Capacitance Measurement: 25pF~100mF
7: Capacitance Resolution: 1pF
8: DC Voltage Measurement: Up to 50V
9: Screen Size: 3.7 * 3cm / 1.45 * 1.18in
10: PCB Size: 7.8 * 6.2cm / 3.1 * 2.44in
11: Weight: 66g / 2.3oz
LCR M328 Detailed Introduction:
Features:
• 128 x 160 TFT color display
• Powered by 9V battery (battery not included)
• New boot voltage detection
• Automatically test the pins of a component and display on the LCD
• Measure the gate threshold voltage and gate capacitance of the MOSFET
• Measure bipolar transistor current amplification factor and base-emitter threshold voltage
• One-button operation, automatic shutdown to avoid unnecessary battery drainage
• Short detection time: only 1.7 seconds (it is normal to take 1 minute for bulk capacitor detection)
Specifications
1: Display: 128 x 160 TFT color display
2: Normal testing speed: 1.7 seconds
3: Shutdown current: 20nA
4: Resistor test range: 0.5 ohms - 50M ohms
5: Inductor test range: 0.01mH - 20H
6: Capacitor test range: 25pF - 100000uF
7: Color: Black
8: Size: 135 x 70 x 25 mm (5.31 x 2.76 x 0.98 in)
9: Weight: 99g (3.5 oz)