|
![](https://ae01.alicdn.com/kf/S0ee5695faa284029a35823c78dff474cN/3.jpg) ![](https://ae01.alicdn.com/kf/S92834ca4eccc490aa51636356b6cf57c8/3.jpg) ![](https://ae01.alicdn.com/kf/S9c2e7903ee044864a23e87d3d02986d6b/3.jpg) ![](https://ae01.alicdn.com/kf/S8e70af25c8024d5ebdb973f2a132bb24P/3.jpg) aHR0cDovL2ZyZWVzaGlwLmNvLmty![](https://ae01.alicdn.com/kf/S0ee5695faa284029a35823c78dff474cN/3.jpg) ![](https://ae01.alicdn.com/kf/S92834ca4eccc490aa51636356b6cf57c8/3.jpg) ![](https://ae01.alicdn.com/kf/S9c2e7903ee044864a23e87d3d02986d6b/3.jpg) ![](https://ae01.alicdn.com/kf/S8e70af25c8024d5ebdb973f2a132bb24P/3.jpg) ![](https://ae01.alicdn.com/kf/S4bd90675e5134e6788f30c09c4b9235bi/3.jpg)
- ¸ðµ¨ ¹øÈ£: K-208
- Çöó½ºÆ½ À¯Çü: ¿¡À̺ñ
- Ç¥ÁØ: ANSI
- Àç·á: Çöó½ºÆ½
- Á¤¿ø ¹° Ä¿³ØÅÍ À¯Çü: ¿©¼º Ä¿³ØÅÍ
- ¿ø»êÁö: Áß±¹
- À¯Çü: °¡µç ¿öÅÍ Ä¿³ØÅÍ
¿É¼ÇÁ¤º¸[(29)WHITE]![](https://ae01.alicdn.com/kf/S92834ca4eccc490aa51636356b6cf57c8/3.jpg_640x640.jpg) Part Description Blossoming Fountain Head Float Hose Anchor Threaded Insert Elbow Piece Large Washer Small Washer Small Orifices And Restrictions Large Plug Threaded Plug Push-in Tube Push-in Plug Tie Wrap Clamp ![](https://ae01.alicdn.com/kf/S9a2c6be9cb384bc7b724a7b29ebf0c4bu.png) Directional "eyeball type with slip nut - This inlet has a slip-nut holding an "eyeball' for water directional control. Use installation instruction 1, page 3 for this type inlet. ? 1-1/2 inch Female threaded inlet - Water enters through a 1-1/2 inch threaded hole. Hole measures approximately 1-3/4 inch across. Use installation instruction 2, page 4 for this type inlet. ? 1 inch Unthreaded inlet - Water enters through a 1 inch unthreaded pipe or a 1 inch hole in a directional "eyebal".Opening measures approximately 1 inch top to bottom. Use installation instruction 3, page 5 for this type inlet. ? Pool cleaner quick disconnect fittings. Refer to Figure 7. Use installation instruction 4, page 6 for this type inlet. ![](https://ae01.alicdn.com/kf/S492495a728b045b0b3ad57c6ad9bd644o.png) ![](https://ae01.alicdn.com/kf/S775ece7578b3453c89f93bdb4c443cafx.png) 1. Insure that the filter is operating and properly maintained. Turn the pump off. 2. Remove the slip nut holding the "eyeball" in place from the inlet nearest the shallow end. Select one of the washers (7 or 8) that best fits into the threaded of the slip nut Insert the elbow piece (6) through the opening in the washer and the through the slip nut (Fig.2). Some smaller inlets will not require a washer. This is your inlet adapter. 3. Refer to Figure 1. Uncoil the hose (3) and remove all twist. Using clamps (15), clamp one end of the hose to the back side of the fountainhead (1). and the other end to inlet adapter from step 2. Cover one set of bleed holes with the hose (Fig. 3). To tighten clamp, grasp "tabs" between thumb and forefiger and squeeze. Tighten securely with a pair of pliers. To open the clamp. grip one "tab" of the clamp with pliers and twist loose. 4. Using the tie wrap (14), LOOSELY attach the anchor (4) to the hose (3). The anchor (4) should be attached to the hose (3) at a point as deep as the water plus approximately two feet. You will have to estimate what the water depth is where you want the fountain and add two feet. CAUTION: DO NOT CONSTRICT THE HOSE BY TIGHTENING THE TIE WRAP (14) TOO TIGHT. 5. Attach the inlet adapter to the pool inlet by screwing the slip-nut back on (Fig.3). 6. Place the fountain assembly into the pool. Position the fountain in the desired location being careful not to crimp the hose (3). 7. Turn the pump on and observe the position and height of the fountain. Turn the pump off and adjust the fountain position if necessary. ![](https://ae01.alicdn.com/kf/S43fffe371a3447aea43ca2a960ef42b4K.png) ![](https://ae01.alicdn.com/kf/S6a1ae081fc6349a59fc710cfbbc33bbah.jpg) ![](https://ae01.alicdn.com/kf/Sddf8f4558ab64457b2558a866fae7ccdH.jpg) ![](https://ae01.alicdn.com/kf/S0ee5695faa284029a35823c78dff474cN.jpg) ![](https://ae01.alicdn.com/kf/S92834ca4eccc490aa51636356b6cf57c8.jpg)
|
|
|
|
|