|
aHR0cDovL2ZyZWVzaGlwLmNvLmty
modname=ckeditor
MTSSeries specification table tension test conditions:Uniform line speed5m/s Subject to the circular skeleton
MTSSeries£¨With attenuation device£©Damping is generated by changing torque through magnetic field conversion£¬No mechanical friction£¬Therefore, it can produce stable tension for a long time.£¬And the accuracy can be effectively guaranteed¡£Can freely adjust the anti-tension£¬Can adapt to the winding of the square skeleton and the winding of the sharp change winding speed£¬No disconnection will occur¡£ When the wire is broken and the wire is used up£¬Notice of equipment disconnection detection device£¬Winding machine automatically stops¡£ New pneumatic attenuation device£¬More suitablePINFast winding of zero tension of feet¡£
¡ÝPrecautions for use: 1¡¢The tension rod is the best working condition when parallel to the plane on the box body.£¬You can also use the appropriate working angle according to the user`s needs.£¬However, the tension rod should not be higher than the red mark on the box surface when working.¡£ 2¡¢Only tension is allowed during work by minor£¬Not allowed by major¡£When the tension needs to be hours by major£¬Must be adjusted in a stop state£¬So as not to cause Broken Line¡£ 3¡¢If there is tension fluctuation in the adjustment£¬After stopping the machine, adjust the tension to the maximum tension.£¬Then slowly return to the desired tension to readjust¡£ 4¡¢Adjustment ends start working£¬The working angle of the tension rod is the same as that of the static installation.£¬Please be sure to re-adjust the tension£¬In order to avoid abnormal wear caused by various components of the tension device£¬And reduce service life¡£
MTS Pneumatic magnetic tension specification table
Model |
Tension range |
Wire diameter is recommended |
MTS 020 |
4.0-40g |
0.03-0.07mm |
MTS 100 |
10-120g |
0.04-0.14mm |
MTS 300 |
50-400g |
0.08-0.25mm |
MTS 600 |
80-600g |
0.12-0.35mm |
MTS 800 |
100-800g |
0.14-0.40mm |
MTS 1200 |
200-1200g |
0.25-0.50mm |
MTS 2000 |
300-2000g |
0.30-0.70mm |
Tension test conditions:Uniform line speed5m/s Subject to the circular skeleton
How to use the tension device to help the product
There is a big difference between using the tension device and not using the tension device on the winding machine.£¬Here we summarize some advantages£¬For reference only 1£ºEnsure the consistency of coil electrical performance and production process technical indicators£» 2£ºThe required tension can be controlled at will with high precision.£¬Improve the appearance of the coil£¬Make the coil flat¡¢Full¡£ 3£ºCan Save paint line£¨May be small by single product£¬If calculated according to the full annual output£¬This number is amazing.£© 4£ºReduce friction£¬Change the patent wire from static friction to dynamic friction£¬Better protection of the lacquer wire insulation layer 5£ºEasy to change the design of the product.
Precautions and maintenance for use of magnetic tension device
The tension rod shall not be higher than the red line position when the tension rod is in working condition.¡£ Only tension is allowed during work by minor£¬Not allowed by major¡£ Tension is required by major hours£¬Must be adjusted in a stop state£¬So as not to cause disconnection¡£ If there is tension fluctuation in the adjustment£¬First adjust the tension to the maximum tension£¬Then slowly return to required Re-adjustment near tension. The mechanical tension device should not be too hard when it is installed.£¬Will affect the firmness of the inlay¡£ Prevent falling£¬Will damage ceramic parts and shells¡£ When the tension rod is installed, the locking screw should be aligned to the axis plane.¡£ Do not use the line when it is not matched with the model.¡£ It is strictly forbidden to add any grease to the damping wheel.¡£ Do not open the back cover without authorization and adjust it yourself.¡£ Regular replacement of wool ring£¬So as not to block the nozzle¡£ If the passing wheel is abnormal or does not turn, please replace it in time.£¬Because the bearing has been worn out¡£ If the damping wheel turns and slips£¬Please use the cotton thread stained with alcohol to rub the inside of the damping wheel.ORing£¬This can? To clear Wax dirt left in the paint line¡£ Keep the production site clean£¬Long dust backlog is easy to wear and tear the tension device parts¡£ If it is not used for a long time or if the tension is unstable after long-term use£¬Please stop£¬Spin from small to large£¬From big to big?? Repeated several times£¬Can restore the initial state¡£ If you use a magnetic tension device with a cylinder£¬Air pressure shall not be lower5Kg
|
|
|
|
|